4/4/2025, 8:40:20 PM 星期五
Study on Rod Diameter Conversion in Hammering Numbers of DPH
CSTR:
Author:
Affiliation:

The Navy Engineering Design and Research Academy

Clc Number:

TU413.9

  • Article
  • | |
  • Metrics
  • |
  • Reference [11]
  • |
  • Related [11]
  • | | |
  • Comments
    Abstract:

    φ42mm rod is regulated for DPH in most standards of China, but a lot of engineering investigation units tend to use φ50mm rods based on the consideration of construction convenience factors. By the analysis on the testing points of DPH and the influencing factors, based on the revision coefficient table of DPH, the derived coefficient of rod diameter conversion is 0.89, which has been verified by a waterway engineering instance in island reefs of Hainan. The results show that for the coral clast formation of buried depth less than 12m in the same geomorphic units, the ratio of hammering numbers of DPH with φ42 drill pipe and DPH with φ50 drill pipe is 0.875, which is in close agreement with the derived results.

    Reference
    [1] GB 50021-2001.岩土工程勘察规范 [S].北京:中国建筑工业出版社,2009.
    [2] 李晓力,肖普,李庆跃.重型动力触探在振冲施工质量控制及检测中的应用[J].探矿工程(岩土钻掘工程),2013,40(2):74-76,80.S
    [3] 曹厚明.重型动力触探、标准贯入试验在振动挤密碎石桩复合地基检测中的应用[J].探矿工程(岩土钻掘工程),2004,31(2):25-25.S
    [4] TB 10018-2003.铁路工程地质原位测试规程 [S].北京:中国铁道出版社,2003.S
    [5] YS 5219-2000.圆锥动力触探试验规程 [S].北京:中国计划出版社,2001.S
    [6] 张平,田红花.有关动力触探影响因素修正问题的探讨[J].沈阳大学学报,1999,11(2):80-83.S
    [7] GB/T 9808-2008.钻探用无缝钢管 [S].北京:中国标准出版社,2009.
    [8] 谢春庆.雅江流域碎石层动力触探试验研究 [J]. 探矿工程(岩土钻掘工程),2004,31(5):4-5.
    [10] 鲁兴社,罗洋.计算动力触探修正系数的多项式拟合法[J].长春工程学院学报(自然科学版),2011, 12(1):39-43.
    [11] 赵昭熔,曹化平.动力触探试验技术的研究与应用[J].铁道工程学报,2005,(Z1):431-439.
    [9] 左永振,程展林,丁红顺,等.动力触探杆长修正系数试验研究 [J].岩土力学,2014,35(5):1284-1288.
    Cited by
    Comments
    Comments
    分享到微博
    Submit
Get Citation
Share
Article Metrics
  • Abstract:931
  • PDF: 1118
  • HTML: 202
  • Cited by: 0
History
  • Received:July 12,2014
  • Revised:July 13,2014
  • Adopted:December 15,2014
  • Online: February 11,2015
Article QR Code